personalized gift for men

personalized wedding gifts personalized wedding gifts

personalized wedding gifts Four-leaf Clover Door Hanger In-the-Hoop decorative pillow shams

Updated: 2020-03-27  Views: 103

In-the-Hoop projects are a fast, easy and consistent way of completing the construction inside the embroidery hoop. The Easy Four-leaf Clover Door Hanger project is made entirely in-the-hoop, which means, when you’;re finished stitching, you’;re done!?The Door Hanger In-the-Hoop can be stitched in three different sizes on your BERNINA embroidery machine and includes a built-in Monogram. As an added bonus, I’;m going to show you what else you can use these glittery clovers for.

Note: Listed below are the materials used in the Four-leaf Clover Door Hanger In-the-Hooppersonalized wedding gifts, for detailed cutting instructions for each size go to Step 1.

personalised gifts

Download the embroidery designs for the Four-leaf Clover Door Hanger below.

Large Size Magic Four-leaf Clover Door Hanger Embroidery Files

Medium Size Magic Four-leaf Clover Door Hanger Embroidery Files

Small Size Magic Four-leaf Clover Door Hanger Embroidery Files

Gather your machine and materials and let’;s get stitching!

Depending on which size Door Hanger in-the-hoop you would like to make, choose the design and monogram and bring to your machine.

Prepare machine for embroidery by attaching the embroidery unit and appropriate presser foot. For the BERNINA 790 Plus I used the?Embroidery foot # 26 (drop-shaped) and the Oval hoop.

Insert a brand new embroidery needle. Note: It’;s nice to begin every project with a brand new needle.

Insert a Bobbin with 60 wt white thread. Thread top of machine with primary color, green. Follow the individual cutting instructions below based on size.

Small (Medium hoop) 100 x 130 materials (Finished measurement 4-1/8″; wide by 4-1/4″; tall)

Medium (Oval hoop) 145 x 255 materials (Finished measurement 6″; wide by 6-1/4″; tall)

Large (Maxi hoop) 210 x 400 materials (Finished measurements 8-1/8″; wide by 8-1/2″; tall)

Press the wrong side of the appliqué to the scratchy side of the fusible web.

Remove the fusible web paper and discard.

Press the wrong side of the applique to one side of the foam. Note: Foam has no right or wrong side.

Hoop the tear away stabilizer and tighten screw.

Sew Stitch #1, the placement stitch. When stitching is complete, remove hoop from machine and place on a flat surface (Do not remove materials from hoop). Fold ribbon in half lengthwise. Place the raw edges about 1/2″; below the center top of? Stitch #1Secure with tape. Note: Be sure the tape is on the outside of Stitch #1.

Place the front centered over Stitch #1. Secure with tape along the top and bottom.

Insert hoop into machine and sew Stitch #2, the secure stitch. Remove hoop from machine and place on a flat surface (Do not remove materials from hoop).

Place the appliqué material, with foam side facing down, centered over the shamrock circle. Secure with tape on all four corners. Insert hoop into machine and sew Stitch #3, the appliqué secure stitch. When stitching is complete, remove hoop from machine and place on a flat surface (Do not remove materials from hoop).

Use duckbill appliqué scissors to cut as close to the secure stitch as possible, without cutting the stitch.

Insert hoop into machine and sew Stitch #4, the appliqué satin stitch.

Each size Shamrock Door Hanger In-the-Hoop includes monogram letters. Note: If you do not want to sew a monogram, skip to step 7. Change the upper thread to the monogram thread color choice.

Sew Stitch #5, the monogram. When stitching is complete, remove hoop from machine and place on a flat surface?(Do not remove materials from hoop).

Turn hoop to wrong side facing up.

Place the back over the stitching, centered within width and height. Tape along the top and bottom to secure. Note: Extend tape past back material all the way to the hoop. Attaching the tape to the hoop will help prevent the tape from shifting or moving while stitching.

Wind a bobbin to match the top thread. This will be for the final outside stitching and will be seen on the front and back of the Four-leaf Clover Door Hanger in-the-hoop.

Insert hoop into machine and sew Stitch #6, the final outside running stitch.

Next, remove hoop from machine. Remove tape.

Now, remove the hoop.

Finally, remove the stabilizer. Note: When removing the stabilizer, be sure not the distort the stitches.

Cut 1/8″; around the outside stitching (Do not cut the Ribbon).

Make one for all your friends and family!

Below shown is Cork fabric. Note: When using cork fabric as the center circle applique, omit the foam.

Experiment with different color ways with thread, appliqué materials and main clover materials. The small four-leaf clover in the upper right hand corner is made of felt.

Hang in your garden and add some gold coins.

Decorate as a wine bottle tag.

Omit the ribbon and use as a coaster.

Get ready for the St. Patrick’;s day party and add some glitter to the gift bag!

Enjoy making magic with your very own Four-leaf Clover hanger In-the-Hoop!

Durable, attractive glassware is a must. Toyo-Sasaki Glass from Japan fits that bill. And it brings even more to the table: a storied history.

You’ll likely notice a new look on the pages of our Fall 2017 catalog, and it’s not just because we’re ready for a new season. We’re launching our latest designer partnership with celebrated decorator Miles Redd. We sat down with the man of the hour to talk about the inspiration behind the pieces he designed for his first collection.

This Holly Berry DIY Ribbon Christmas Wreath is so simple to make! Invite a few friends over to make one and have a Holiday Crafternoon! ?This project is sponsored by Make It Fun Crafts, all ideas, work, opinions and crazy ideas are 100% mine.



Powered by personalized gift for men @2018 RSS Sitemap html Sitemap

Copyright 站群系统 © 2013-2019 Personalize

top